Bad Dragon Measurements Sheet - from users for users

[Yak]

I have a question about an unusual measurement that users might be able to provide:

I'm thinking about getting a Lil Squirt, then mounting it upon a thin steel rod as an adornment on something. Problem is, there's no measurements about the cumtube diameter. Can somebody measure what the diameter is of a cumtube hole in a Lil Squirt? Is the diameter consistent throughout the toy? Thanks! Approximate is ok, I just want to know if I'd be dealing with something a little too small or a little too big. Thanks!

Just Measured our Lil Squirt (Spritz)

the Cumtube itself is close to 6mm...

from what I gather the hole is close to 8mm

(millimeters)

good luck!

[ArkonInu]

Large Austin the Fox

Tip to beginning of knot: 10 cm -> 3.94 inch

Tip to end of knot: 15.5 cm -> 6.1 inch

Tip to base (Usable Length): 18.3 cm -> 7.2 inch

Total Length: 22 cm = 8.66 inch

Circumference of shaft: 13.5 cm -> 5.31 inch

Circumference of knot: 18.8 cm -> 7.4 inch

Circumference of stem: 12 cm -> 4.72 inch

Circumference of base: 27 cm -> 10.63 inch

[ArkonInu]

Large David the Werewolf

Tip to beginning of knot: 12 cm -> 4.72 inch

Tip to base (usable length): 21 cm -> 8.27 inch

Total length: 24 cm -> 9.45 inch

Circumference of head: 17 cm -> 6.69 inch

Circumference directly after head: 16.5 cm -> 6.5 inch

Circumference of shaft: 17.3 cm -> 6.81 inch

Circumference of knot: 22.5 cm -> 8.86 inch

Circumference of stem: 18 cm -> 7.09 inch

Circumference of base: 30.5 cm -> 12 inch

I wonder how BD measures the head, since the head to shaft difference on the product page is way bigger

[ArkonInu]

Extra Large David the Werewolf

Tip to beginning of knot: 15.2 cm -> 5.98 inch

Tip to base (usable length): 27 cm -> 10.63 inch

Total length: 31.4 cm -> 12.36 inch

Circumference of head: 21.5 cm -> 8.46 inch

Circumference directly after head: 20.6 cm -> 8.11 inch

Circumference of shaft: 21 cm -> 8.27 inch

Circumference of knot: 28.2 cm -> 11.1 inch

Circumference of stem: 21.3 cm -> 8.39 inch

Circumference of base: 38 cm -> 14.96 inch

He is one of my favorite toys

[ArkonInu]

Extra Large Rex the German Shepherd

Tip to beginning of knot: 19.2 cm -> 7.56 inch

Tip to end of knot: 26.5 cm -> 10.43 inch

Tip to base (Usable Length): 30 cm -> 11.81 inch

Total Length: 36 cm -> 14.17 inch

Circumference of shaft: 19.4 cm -> 7.64 inch

Circumference just before the knot starts: 14.6 cm -> 5.75 inch

Circumference of knot: 29 cm -> 11.42 inch

Circumference of stem: 16.5 cm -> 6.5 inch

Circumference of base: 40.2 cm -> 15.83 inch

No knot locks better than rex in my experience, but rex also can't stand on his own

[ArkonInu]

So, that's it for now, hit me up what toy I should measure next (the list of my collection is in my signature)

I also hope that I made the metric to imperial conversion right, double check won't hurt for sure

[Watervixen]

Swamp Wyrm M measurements

[Watervixen]

Nova M
Sleipnir Mini

[Watervixen]

Crackers M
Hanns

[Yak]

Can anyone post measurements for Kage, and Small and/or Med Spritz?
thanks!

[PrinceMoonbutt]

So, that's it for now, hit me up what toy I should measure next (the list of my collection is in my signature)

Could you measure your large Cole? I am fairly interested in getting one down the line.

As for my contribution, I notice the list lacks Kippy, so here is mine (in inches):

Usable Length: 7.25

Length Before Knot: 4.2

Shaft Circumference: 5.9375 (5 & 5/16)

Head Circumference: 5.25

Knot Circumference: 7.75

Stem Circumference: 5.625

Some are rounded slightly (Who knew holding a camera and a flexible tape measure at the same time was tough?). Also I am alright with being a volunteer for the thing if people need to ask about the toy.

[Barghest]

Could somebody with a small David please measure the circumference of the shaft below the knot and the circumference of the base itself please? I've got one ordered and I need to figure out what size o-ring I need to buy to attach it to my harness.

[Fae Fantase]

Could somebody with a small David please measure the circumference of the shaft below the knot and the circumference of the base itself please? I've got one ordered and I need to figure out what size o-ring I need to buy to attach it to my harness.

I measured it came out to 8" base circumference, 5" exactly below the swell. Hope your werewolf turns put lovely !

[Barghest]

[colour=#BFFFFF]I measured it came out to 8" base circumference, 5" exactly below the swell. [/color] Hope your werewolf turns put lovely !

That's excellent! Thank you!

(The toy's just a flop with a white base and a red shaft, but that was the exact colour scheme I wanted and I wasn't going to say no to $56 for a toy with split firmness and a cumtube!)

[Fae Fantase]

That's excellent! Thank you!

(The toy's just a flop with a white base and a red shaft, but that was the exact colour scheme I wanted and I wasn't going to say no to $56 for a toy with split firmness and a cumtube!)

Congrats ! Gotta love finding the perfect flops/Frankenpours!

[Raven]

Updated, sorry for taking so long.

[ShiftingMist]

Can someone who has a small and medium ultimate fantasy and/or small and medium anthro dragon please give me the measurements for the largest circumference on the models? I believe for the anthro that should be the uncircumcised bit of the head. it looks like the UF is standard girth for most of the shaft? Thanks

[Grimly Fiendish]

Updated, sorry for taking so long.

This is awesome, thanks for doing it, and thanks to all the contributors.

[Harbenz]

XL Clayton
Tip 7.93" (20 cm)
Base 11.75" (29'8 cm)
Insertable 10.5" (26'7 cm)

► Show Spoiler

Tape is a bit moved, is 10.5"

XL Tyson
Head 8" (20'3 cm)
Shaft 6.5" to 7" (16'5 to 17'8 cm)
Biggest ring 8.2 (20'8 cm)
Insertable 11.75" (29'8 cm)

► Show Spoiler

[Zaneta]

Can someone grab me measurements for medium david?